features : ACTF8035 - 868.35 - dcc6v1.0 saw filter ? low - loss rf filter ? high rejection ? single en ded operation at 50 with matching ? ceramic package for s urface m ounted t echnology ( smt ) ? lead- free production and rohs compliance package dimension s ceramic package: dcc6 pin configuration 2 input 5 output 1, 3, 4, 6 case ground 1, 3, 4, 6 to be grounded marking top view, laser printing " act ?: manufacturer?s mark ? f ?: saw filter ? 8035 ?: part number ? ?: terminal 1 ??: lot number (the code shown below varies in a 4 - year cycle) code 1 2 3 4 5 6 7 8 9 10 11 12 2013 a b c d e f g h j k l m 201 4 n p q r s t u v w x y z 201 5 a b c d e f g h i j k m 201 6 n p q r s t u v w x y z maximum ratings rating value unit operating t emperature r ang e t a -4 0 ~ + 85 c storage t emperature r ange t stg -40 ~ + 85 c dc v oltage ( between any t erminals ) v dc 10 v rf power (in bw ) p 10 dbm
electrical characteristics characteristic minimum typical maximum unit center frequency @25 f c 868.350 mhz insertion loss il -- 3 .5 4. 8 db 3db bandwidth bw 3 1800 khz attenuation: (relative to il min ) 10.0 ? 700.0 mhz 700.0 ? 830.0 mhz 830.0 ? 850.0 mhz 850.0 ? 864.4 mhz 872.4 ? 877.4 mhz 877.4 ? 882.4 mhz 882.4 ? 900.0 mhz 900.0 ? 1000.0 mhz rel 50 38 32 22 16 24 28 40 55 43 38 27 20 28 35 45 db temperature frequency temperature coefficient ftc 0.032 ppm/ 2 frequency aging absolute value during th e first year | fa | 10 ppm/yr rohs c ompli ant electrostatic sensitive device typical frequency response
stability c haracteristics test item condition of test 1 mechanical shock (a) drops: 3 times on concrete floor (b) height: 1.0 m 2 vibration resistance (a) frequency of vibration: 10 ~ 55hz (b) amplitude: 1.5 mm (c) directions: x,y and z (d) duration: 2 hours 3 moisture resistance (a) condition: 40c, 90~95% r.h. (b) duration: 96 hours (c) wait 4 hours before measurement 4 climatic sequence (a) + 70c for 16 hours (b) +55 c for 24 hours, 90~95% r.h. (c) -25c for 2 hours (d) +40 c for 24 hours, 90~95% r.h. (e) wait 4 hours before measurement 5 high t emperature e xposure (a) temperature: 70c (b) duration: 250 hours (c) wait 4 hours before measurement 6 thermal impact (a) +70c for 30 minutes ? - 25c for 30 minutes repeated 3 times (b) wait 4 hours before measurement requirements : the saw filer shall remain w ithin the electrical specifications after tests. remarks ? saw devices should not be used in any type of fluid such as water, oil, organic solvent, etc. ? be certain not to apply voltage exceeding the rated voltage of components. ? do not operate outside the recommended operating temperature range of components. ? sudden change of temperature shall be avoided, deterioration of the characteristics can occur. ? be careful of soldering temperature and duration of components when soldering. ? do not place soldering iron on the bod y of components. ? be careful not to subject the terminals or leads of components to excessive force. ? saw devices are electrostatic sensitive . p lease avoid static voltage during operation and storage. ? u ltrasonic cleaning shall be avoided . ultrasonic vibratio n may cause destruction of components. test circuit recommended land pattern
packing information carrier tape reel dimensions outer packing type quantity dimension description weight carton box 0.85 carton box 2 0000 190190190 1. 7 0 unit: mm unit: kg
recommended soldering profile c e a act . all rights reserved. 1. the specifications of this device are subject to change or obsolescence without notice. 2. typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. 3. our liability is only assumed for the surface acoustic wave (saw) component(s) per se, not for applications, processes and circuits implemented within components or assemblies.
|
